AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Who makes subaru super coolant8/31/2023 ![]() The Radweld bottle bears a striking resemblance to the SUBARU cooling system conditioner bottle (except for the label). So it would appear the SUBARU cooling system conditioner may be manufactured by Holts in the UK. ![]() However, even the casual observer cannot miss the "Holts" embossed on the blue plastic bottle. ![]() The bottle label states "Manufactured in England for Subaru of America, Inc.". Who manufactures the SUBARU cooling system conditioner? Similar products use ingredients such as ginger. The common headgaket failures of these engines was caused by a chemical breakdown of the gasket. It was meant to combat the leaking headgaskets on the NON-turbo legacys of the early 2000s. Its the absolute best choice when searching for. I believe the linseed meal is what can be seen as the chunks in the product. The conditioner will gunk up your entire cooling system and cause it to underperform. Genuine Subaru engine coolant is fully-formulated, corrosion inhibited, ethylene glycol based and ready to use. What is in the SUBARU cooling system conditioner?Īccording to the product label, it contains a proprietary resin solution, borax decahydrate, and linseed meal. SUBARU vehicles starting around 2008-2009 started using the blue SUBARU super coolant. Now the caveat would be the statement might be valid only for SUBARU vehicles that used the traditional SUBARU coolant. Genuine Subaru Cooling System Conditioner has been tested and approved for aluminum engines and radiators. Whenever the coolant is changed, you must add Genuine Subaru Cooling System Conditioner. Moreover, SUBARU TSB 09-47-07 titled "Cooling System - Coolant Flushing Machines and Additives" stated: Fuji doesn’t approve of any aftermarket additive whatsoever, so why argue? Take four ounces of coolant out of the radiator, shake the bottle, then pour the contents directly into the radiator filler neck, not the overflow jug. You, too, should be using it every time you drain and refill a Subaru cooling system. Antifreeze/Coolant Prestone All Makes & Models Extended Life Antifreeze/Coolant. An SUBARU cooling system article titled "Cooling System Overview" from May 2005, in a section discussing Genuine Subaru Cooling System Conditioner (Part Number SOA345001) added, stated: With all the types of coolants listed down, I will end this short post by shedding light on some common myths and trying to clear them. The specific VIN ranges are as listed below:Ĭan I use the SUBARU cooling system conditioner even if my SUBARU isn't in the list above? HOAT is used by Volkswagen (G12++ and G13) and is also reverse compatible with OAT (G12 and G12++ that I mentioned before). 2000-2002 MY Subaru Legacy and Outback with 2.5L engine.Namely these included the following SUBARU vehicles (within a certain VIN range): Warranty Disclaimer: Subaru of America will only warranty parts installed by a CERTIFIED Subaru Dealership. What SUBARU vehicles require the cooling system conditioner?Ĭertain model SUBARU vehicles were listed in SUBARU bulletin WWP-99 were supposed to have the conditioner added. Part : subSOA868V9270 Subaru 08+ All Models Super Coolant Blue (1 gallon) 50/50 Pre-MixedWarranty Disclaimer: Subaru of America will only warranty parts installed on a car that has a matching VIN to that part. The SUBARU cooling system conditioner is a product intended to be added to the engine coolant when it is changed. If a flowing sound can be heard (from the heater core in the cabin) repeat this process from step 17 on.What is the SUBARU Cooling System Conditioner? Re-attach the radiator cap and twist to seal it.Ģ0) Set the heater to the maximum hot position and set the blower speed to "LO." Start the engine, and race to 3000rpm several times. Also, add coolant to the overflow reservoir until it reaches the "Full" line. If the coolant level has dropped add coolant until the level reaches the filler neck. Be careful with the coolant temperature to avoid overheating the engine.ġ8) Stop the engine and wait until the engine coolant temperature lowers to at most 86 degrees F.ġ9) Open the radiator cap. Close the air bleeder plug.ġ5) Re-attach the radiator and reservoir caps.ġ6) Start the engine and turn the heater on to the maximum hot position with the blower speed set to "LO."ġ7) Run the engine at 2000rpm until the radiator fan starts and stops. Add coolant to the radiator until the fluid level reaches the radiator neck. If the coolant level has dropped, open the air bleeder plug in the heater hose. This coolant is pre-mixed and so ALL you need to. Spend no longer than 40 seconds completing this step.ġ3) Wait for an entire minute and then remove the radiator cap. PN: SOA868V9270 Factory fill from Subaru on ALL 2008+ Imprezas and 2009+ Foresters and 2010+ Legacy models. ![]() Start the engine and race the engine 5 times to about 3000rpm. Otherwise continue filling the radiator.ġ1) Fill the coolant overflow reservoir until the level reaches "Full."ġ2) Replace the radiator cap, and twist to seal it. If the level dropped, fill it back up to the filler neck.ġ0) Close the air bleeder plug once fluid starts to come out of it. 9) Check the coolant level in the radiator.
0 Comments
Read More
Leave a Reply. |